EXAMEN CORRESPONDIENTE CCNA3 V6
Scaling Networks v6.0 (Actualizado 2019)
Capitulo 1 Preguntas y respuestas Inglés y Español
Capitulo 2 Preguntas y respuestas Inglés y Español
Capitulo 3 Preguntas y respuestas Inglés y Español
Capitulo 4 Preguntas y respuestas Inglés y Español
Capitulo 5 Preguntas y respuestas Inglés y Español
Capitulo 6 Preguntas y respuestas Inglés y Español
Capitulo 7 Preguntas y respuestas Inglés y Español
Capitulo 8 Preguntas y respuestas Inglés y Español
Capitulo 9 Preguntas y respuestas Inglés y Español
EXAMEN CCNA3 V6 CAPITULO 5
ESPAÑOL (AL FINAL VERAS LA VERSION EN INGLES).
1
Un administrador de red sólo ha cambiado el ID del router en un router que está trabajando en un entorno OSPFv2. ¿Qué debe hacer el administrador para restablecer las adyacencias y utilizar el nuevo ID de router?
Emita el proceso ip ospf clara comando modo privilegiado. *
Configure las declaraciones sobre la red.
Cambie el ID de proceso OSPFv2.
Cambiar la prioridad de la interfaz.
2
Consulte la presentación. ¿Qué tres conclusiones se pueden sacar de la salida que se muestra? (Elija tres.)
El DR se puede llegar a través de la interfaz GigabitEthernet 0/0. *
Ha habido 9 segundos desde el último paquete de saludo enviado. *
La ID del router en el router DR es 3.3.3.3
El BDR tiene tres vecinos.
Los valores de ID de router no fueron los criterios utilizados para seleccionar el DR y el BDR. *
Esta interfaz está utilizando la prioridad predeterminada.
3
Tras un análisis de una tabla de enrutamiento, un técnico de la red se da cuenta de la siguiente entrada:
O * E2 0.0.0.0/0 [110/1] a través de 192.168.16.3, 00:20:22, Serial0 / 0/0
¿Qué información se desprende de esta producción?
Esta ruta es una ruta por defecto propagado. *
El frontal del área OSPF 0 es la interfaz que se dirige 192.168.16.3.
La ruta se encuentra a dos saltos de distancia.
La métrica de esta ruta es de 110.
4
¿Qué comando se un tema ingeniero de la red para verificar la hola configurado y los intervalos de temporizador muertos en un enlace punto a punto WAN entre dos routers que ejecutan OSPFv2?
serie show interface ipv6 ospf 0/0/0
espectáculo ip ospf neighbor
show ip ospf interface serial 0/0/0 *
show ip ospf interface FastEthernet 0/1
5
Un ingeniero de la red se ha configurado manualmente el intervalo de saludo a 15 segundos en una interfaz de un router que ejecuta OSPFv2. Por defecto, la forma en que el intervalo muerto en la interfaz se ve afectada?
El intervalo muerto no va a cambiar a partir del valor predeterminado.
El intervalo muerto ahora será de 30 segundos.
El intervalo muerto ahora será de 15 segundos.
El intervalo muerto ahora será de 60 segundos. *
6
Consulte la presentación. Un administrador está tratando de configurar R1 para funcionar OSPFv3 pero la adyacencia de vecinos no se está formando con el router conectado a Fa0 / 0. ¿Cuál es la causa del problema?
FastEthernet0 / 0 se ha configurado como una interfaz pasiva.
Sin ID de router ha sido configurado. *
Una dirección local de vínculo no se ha configurado en la interfaz FastEthernet0 / 0.
Los valores de ID de proceso y de área OSPF son hacia atrás en la configuración de la interfaz.
7
Consulte la presentación. Un administrador de red ha configurado los temporizadores OSPF a los valores que se muestran en el gráfico. ¿Cuál es el resultado de tener esos temporizadores configurados manualmente?
El temporizador de tiempo muerto R1 expira entre los paquetes de saludo de R2. *
La adyacencia de vecinos se ha formado.
R1 ajusta automáticamente sus propios temporizadores para que coincida con los temporizadores R2.
El temporizador hola en R2 expira cada diez segundos.
8
Cuando los vecinos OSPFv2 están estableciendo adyacencias, en el que el estado es lo que eligen a un router DR y BDR?
Estado de dos vías *
Cargando estado
Estado Inicial
Cambio de estado
9
Consulte la presentación. R1 y R2 están conectados al mismo segmento de LAN y están configurados para ejecutarse OSPFv3. Ellos no están formando una adyacencia vecina. ¿Cuál es la causa del problema?
Los identificadores de proceso OSPFv3 de R1 y R2 son diferentes.
El valor de prioridad de ambos R1 y R2 es 1.
Los intervalos de temporizador de R1 y R2 no coinciden. *
Las direcciones IPv6 de R1 y R2 no están en la misma subred.
10
Consulte la presentación. ¿Qué tipo de autenticación de OSPF se ha configurado en esta interfaz?
nulo
simple
MD5 *
texto plano
11
¿Por qué es la autenticación MD5 más segura que la autenticación simple para actualizaciones OSPF?
MD5 no envía la contraseña al router vecino. *
MD5 requiere contraseñas que son al menos 8 caracteres de longitud.
MD5 utiliza tanto un nombre de usuario y una contraseña para autenticar al prójimo.
MD5 emplea IPsec para mantener las actualizaciones sean interceptados.
12
¿Qué dos piezas de información son utilizados por el algoritmo MD5 de OSPF para generar una firma?(Elija dos.)
OSPF router ID
clave secreta *
nombre de host del router
dirección IP de la interfaz
Mensaje OSPF *
13
Un ingeniero de la red está solucionando problemas de convergencia y de adyacencia en una red OSPFv2 y ha señalado que algunas entradas esperadas ruta de red no se muestran en la tabla de enrutamiento. ¿Qué dos comandos proporcionará información adicional sobre el estado de las adyacencias del router, intervalos de temporizador, y el ID de área? (Elija dos.)
show running-configuración
show ip ospf vecino *
mostrar interfaz ip ospf *
show ip ospf ruta
mostrar ip protocols
14
¿Por qué OSPF interfaces en serie por lo general requieren un ancho de banda de configuración manual?
OSPF utiliza el valor de ancho de banda para calcular rutas para su tabla de enrutamiento. *
Todas las interfaces de serie por defecto a un valor de 1.544 Mb / s.
Cada lado de un enlace serie OSPF debe configurarse con un valor único.
Valor de ancho de banda afecta a la velocidad real del enlace.
15
Un ingeniero de la red está solucionando un red OSPFv2 y descubre que dos routers conectados por un enlace WAN serie punto a punto no están estableciendo una adyacencia. El proceso de enrutamiento OSPF, comandos de red y zona ID están todos confirmada como correcta, y las interfaces no son pasivos. Las pruebas muestran que el cableado es correcto, que el enlace está activo, y pings entre las interfaces tienen éxito. Lo más probable es el problema?
Una tasa de reloj no se ha establecido en la interfaz DCE del enlace serie.
Los identificadores de proceso OSPFv2 de cada router no coinciden.
Una elección DR no ha tenido lugar.
Las máscaras de subred en las dos interfaces seriales conectadas no coinciden. *
16
Un ingeniero de la red está solucionando problemas de enrutamiento OSPFv2 en dos routers conectados. ¿Qué dos requisitos para formar una necesidad de adyacencia para ser verificada? (Elija dos.)
Verifique que las interfaces que conectan los dos routers están en la misma zona. *
Verifique que uno de los routers es el DR o BDR y otro router DROther.
Compruebe que una de las interfaces que conectan los dos routers está activa y la otra pasiva.
Verifique que las interfaces que conectan los dos routers están en la misma subred. *
Verifique que ambos routers están utilizando el mismo OSPFv2 ID del proceso.
17
¿Qué comando se utiliza para verificar que OSPF está habilitado y también proporciona una lista de las redes que se anuncian por la red?
mostrar los protocolos IP *
show interface ip ospf
mostrar breve interfaz ip
show ip ospf ruta
18
Consulte la presentación. Cuatro routers están conectados a un segmento de Ethernet LAN y están configurados para ejecutarse OSPFv3. Sin embargo, ninguno de los routers están recibiendo actualizaciones de enrutamiento. ¿Cuál es la causa del problema?
Los routers utilizan direcciones locales de enlace IPv6 para comunicarse.
El tipo de red se ha ajustado a BROADCAST en lugar de NBMA.
Los routers están utilizando direcciones IPv4 para los ID de router.
Todos los routers tienen una prioridad de interfaz OSPFv3 de 0. *
19
Consulte la presentación. Estos dos routers están configurados para ejecutarse OSPFv3 pero no están formando una adyacencia vecina. ¿Cuál es la causa del problema?
Los routers no tienen direcciones IPv6 globales que se configuran en los Fa0 / 0 interfaces.
Los routers de ambos han sido elegidos como el DR.
Los routers están configurados con el mismo ID de router. *
Los routers tienen la misma prioridad.
20
Un ingeniero de redes sospecha que los routers OSPFv3 no están formando adyacencias de vecinos porque hay desajustes temporizador de interfaz. ¿Qué dos comandos se pueden emitir en la interfaz de cada router OSFPv3 para resolver todas las desigualdades del temporizador? (Elija dos.)
no ospf dead-ipv6 intervalo *
sin router ospf ipv6 10
ip ospf dead-intervalo de 40
no ospf hello-ipv6 intervalo *
no ospf ipv6 costó 10
ip ospf hello-intervalo de 10
21
Consulte la presentación. Llena el espacio en blanco. No utilizar abreviaturas.
El comando “show ipv6 route” puede ser emitida en el router R2 para verificar la propagación de una ruta estática por defecto de R1 a R2.
22
Llena el espacio en blanco. No utilizar abreviaturas.
Cuando se están utilizando IPv4 y OSPFv2, el comando “show ip ospf vecino” se utiliza para verificar que un router se ha formado una adyacencia con los routers vecinos.
23
Colocar las opciones en el orden siguiente:
– No anotó –
estado completo
estado de carga
Estado ExStart
24
Colocar las opciones en el orden siguiente:
Tercero [+]
[+] Segundos
– No anotó –
[+] Primero
[+] Cuarto
[+] El orden no importa dentro de este grupo.
English
1
A network administrator has just changed the router ID on a router that is working in an OSPFv2 environment. What should the administrator do to reset the adjacencies and use the new router ID?
Issue the clear ip ospf process privileged mode command.*
Configure the network statements.
Change the OSPFv2 process ID.
Change the interface priority.
2
Refer to the exhibit. What three conclusions can be drawn from the displayed output? (Choose three.)
The DR can be reached through the GigabitEthernet 0/0 interface.*
There have been 9 seconds since the last hello packet sent.*
The router ID on the DR router is 3.3.3.3
The BDR has three neighbors.
The router ID values were not the criteria used to select the DR and the BDR.*
This interface is using the default priority.
3
When checking a routing table, a network technician notices the following entry:
O*E2 0.0.0.0/0 [110/1] via 192.168.16.3, 00:20:22, Serial0/0/0
What information can be gathered from this output?
This route is a propagated default route.*
The edge of the OSPF area 0 is the interface that is addressed 192.168.16.3.
The route is located two hops away.
The metric for this route is 110.
4
Which command will a network engineer issue to verify the configured hello and dead timer intervals on a point-to-point WAN link between two routers that are running OSPFv2?
show ipv6 ospf interface serial 0/0/0
show ip ospf neighbor
show ip ospf interface serial 0/0/0*
show ip ospf interface fastethernet 0/1
5
A network engineer has manually configured the hello interval to 15 seconds on an interface of a router that is running OSPFv2. By default, how will the dead interval on the interface be affected?
The dead interval will not change from the default value.
The dead interval will now be 30 seconds.
The dead interval will now be 15 seconds.
The dead interval will now be 60 seconds.*
6
Refer to the exhibit. An administrator is trying to configure R1 to run OSPFv3 but the neighbor adjacency is not forming with the router connected to Fa0/0. What is the cause of the problem?
FastEthernet0/0 has been configured as a passive interface.
No router ID has been configured.*
A link-local address has not been configured on interface FastEthernet0/0.
The OSPF process ID and area values are backwards in the interface configuration.
7
Refer to the exhibit. A network administrator has configured the OSPF timers to the values that are shown in the graphic. What is the result of having those manually configured timers?
The R1 dead timer expires between hello packets from R2.*
The neighbor adjacency has formed.
R1 automatically adjusts its own timers to match the R2 timers.
The hello timer on R2 expires every ten seconds.
8
When OSPFv2 neighbors are establishing adjacencies, in which state do they elect a DR and BDR router?
Two-Way state*
Loading state
Init state
Exchange state
9
Refer to the exhibit. R1 and R2 are connected to the same LAN segment and are configured to run OSPFv3. They are not forming a neighbor adjacency. What is the cause of the problem?
The OSPFv3 process IDs of R1 and R2 are different.
The priority value of both R1 and R2 is 1.
The timer intervals of R1 and R2 do not match.*
The IPv6 addresses of R1 and R2 are not in the same subnet.
10
Refer to the exhibit. What kind of OSPF authentication has been configured on this interface?
null
simple
MD5*
plain text
11
Why is MD5 authentication more secure than simple authentication for OSPF updates?
MD5 does not send the password to the neighbor router.*
MD5 requires passwords that are at least 8 characters long.
MD5 uses both a username and a password to authenticate the neighbor.
MD5 employs IPsec to keep the updates from being intercepted.
12
Which two pieces of information are used by the OSPF MD5 algorithm to generate a signature? (Choose two.)
OSPF router ID
secret key*
router hostname
interface IP address
OSPF message*
13
A network engineer is troubleshooting convergence and adjacency issues in an OSPFv2 network and has noted that some expected network route entries are not displayed in the routing table. Which two commands will provide additional information about the state of router adjacencies, timer intervals, and the area ID? (Choose two.)
show running-configuration
show ip ospf neighbor*
show ip ospf interface*
show ip route ospf
show ip protocols
14
Why do OSPF serial interfaces usually require manual bandwidth configuration?
OSPF uses the bandwidth value to compute routes for its routing table.*
All serial interfaces default to a value of 1.544 Mb/s.
Each side of an OSPF serial link should be configured with a unique value.
Bandwidth value affects the actual speed of the link.
15
A network engineer is troubleshooting an OSPFv2 network and discovers that two routers connected by a point-to-point WAN serial link are not establishing an adjacency. The OSPF routing process, network commands and area ID are all confirmed as correct, and the interfaces are not passive. Testing shows that the cabling is correct, that the link is up, and pings between the interfaces are successful. What is most likely the problem?
A clock rate has not been set on the DCE interface of the serial link.
The OSPFv2 process IDs on each router do not match.
A DR election has not taken place.
The subnet masks on the two connected serial interfaces do not match.*
16
A network engineer is troubleshooting OSPFv2 routing issues on two connected routers. Which two requirements to form an adjacency need to be verified? (Choose two.)
Verify that the interfaces that connect the two routers are in the same area.*
Verify that one of the routers is the DR or BDR and the other router a DRother.
Verify that one of the interfaces that connects the two routers is active and the other passive.
Verify that the interfaces that connect the two routers are in the same subnet.*
Verify that both routers are using the same OSPFv2 process ID.
17
Which command is used to verify that OSPF is enabled and also provides a list of the networks that are being advertised by the network?
show ip protocols*
show ip ospf interface
show ip interface brief
show ip route ospf
18
Refer to the exhibit. Four routers are connected to an Ethernet LAN segment and are configured to run OSPFv3. However, none of the routers are receiving routing updates. What is the cause of the problem?
The routers are using IPv6 link local addresses to communicate.
The network type has been set to BROADCAST instead of NBMA.
The routers are using IPv4 addresses for router IDs.
All of the routers have an OSPFv3 interface priority of 0.*
19
Refer to the exhibit. These two routers are configured to run OSPFv3 but they are not forming a neighbor adjacency. What is the cause of the problem?
The routers do not have global IPv6 addresses that are configured on the Fa0/0 interfaces.
The routers have both been elected as the DR.
The routers are configured with the same router ID.*
The routers have the same priority.
20
A network engineer suspects that OSPFv3 routers are not forming neighbor adjacencies because there are interface timer mismatches. Which two commands can be issued on the interface of each OSFPv3 router to resolve all timer mismatches? (Choose two.)
no ipv6 ospf dead-interval*
no ipv6 router ospf 10
ip ospf dead-interval 40
no ipv6 ospf hello-interval*
no ipv6 ospf cost 10
ip ospf hello-interval 10
21
Refer to the exhibit. Fill in the blank. Do not use abbreviations.
The command ” show ipv6 route ” can be issued on router R2 to verify the propagation of a static default route from R1 to R2.
22
Fill in the blank. Do not use abbreviations.
When IPv4 and OSPFv2 are being used, the command “ show ip ospf neighbor ” is used to verify that a router has formed an adjacency with its neighboring routers.
23
Place the options in the following order:
– not scored –
full state
loading state
ExStart state
24
Place the options in the following order:
[+] third
[+] second
– not scored –
[+] first
[+] fourth
[+] Order does not matter within this group.